Problum with high end on gears.
  • bigdog1
    Posts:4
    Joined:Tue Dec 18, 2007 9:16 am
    Problum with high end on gears.

    by bigdog1 » Tue Mar 11, 2008 5:13 am

    Purchased a 2008 crf 150r and installed a yoshimira silencer spark arrestor "slip on" . Due to the bike being new and not broke in my son took it easy after third ride I took it out and noticed that at the top of every gear the bike sputter's out. Yoshimira says that you do not need to rejet I have not made any other mods to bike. !! Please Help !! I am not even sure if the bike always had the problum before installing slip on due to it being new.
  • hondapunk53
    Posts:154
    Joined:Thu May 29, 2008 8:38 pm

    Re: Problum with high end on gears.

    by hondapunk53 » Wed Jun 18, 2008 3:28 pm

    yoshimura means after you jet it first with the stock pipe on so look into what other people are jetting thier 150s at. and i am looking for a pipe too, how does the yoshimura pipe work on a scale of 1 to 10
  • User avatar
    124
    Posts:3704
    Joined:Wed Feb 16, 2005 1:37 pm

    Re: Problum with high end on gears.

    by 124 » Thu Jun 19, 2008 5:31 am

    bigdog1 wrote:Purchased a 2008 crf 150r and installed a yoshimira silencer spark arrestor "slip on" . Due to the bike being new and not broke in my son took it easy after third ride I took it out and noticed that at the top of every gear the bike sputter's out. Yoshimira says that you do not need to rejet I have not made any other mods to bike. !! Please Help !! I am not even sure if the bike always had the problum before installing slip on due to it being new.


    I'd be certain it's not the rev limiter. Just sayin.
    With a pipe, you typically increase air flow. Which in turn increases fuel demand. You may need to increase a main jet size and/or raise the float level. Both of which may cause your symptoms. I would also check what others are running for jetting. I would imagine that a pipe is the most common upgrade to the 150R...

    Good luck.
    70' Honda CT70 (Trail 70; Gold)
    16' KX450
    16' KX85
    12' YZ125
  • [email protected]
    Posts:5039
    Joined:Sun Aug 14, 2005 6:21 pm

    by [email protected] » Thu Jun 19, 2008 5:57 am

    I'd be certain it's not the rev limiter. Just sayin

    And I am certain it is the rev limiter ! :lol:
    It is.
    We get around a post a month describing what you're describing and you are hitting the rev limiter.It's always the rev limiter.
    If you shift up and it goes away... you're hitting the rev limiter.
    Glad to have you here on the site too, let us know how we can help you.
    This guy arrives at needle taper and jetting sizes by tuning the bikes on a dyno with exhaust gas temp and content analysis. It takes the guess work out of setting up your jetting, and there are a ton of very happy owners running his set-ups :
    http://www.crfsonly.com/catalog/product ... ts_id/2253
    This will make your life a lot easier too, just remember to use the spring, o-ring and washer from your OEM fuel screw on this one :
    http://www.crfsonly.com/catalog/product ... ts_id/1333
    Even with the jetting really dialed there'll be days where it's lots cooler,hotter and /or humidity changes. You'll need to tweak the fuel screw an 8th of a turn either way or so when that happens and this fuel screw replaces the very hard to access OEM fuel screw.
    Note also the heavier you are compared to the bikes "target" rider the faster you'll get to the rev limiter. Doug
  • User avatar
    woodsman
    Posts:2065
    Joined:Mon Oct 30, 2006 9:00 pm

    by woodsman » Thu Jun 19, 2008 7:53 am

    Describe the sputtering. The rev limiter is a very obvious thing, and I think he would know if he were hitting it. To see if it is the rev limiter, put it in neutral and rev it till it cant go any higher. If you get the same cut out, it's the rev limiter.
    Currently, 05 450X
    Previously, KTM 790 Adv R, Cbr600rr, Crf450R, Crf250X
  • [email protected]
    Posts:5039
    Joined:Sun Aug 14, 2005 6:21 pm

    by [email protected] » Thu Jun 19, 2008 9:10 am

    The rev limiter is a very obvious thing, and I think he would know if he were hitting it
    .
    Nope.
    It's not at all an obvious thing when people aren't familiar with these bikes and their high rpm operation.
    What is obvious is for the vast majority of cases when someone writes in with a high rpm "bog" or what he's describing that it turns out to be the rev limiter.
    Simply revving the engine without it being under load tells him nothing.
    If the sputtering ceases after up-shifting it's the rev limiter.
    Find a post where the mysterious high rpm "bog" goes away magically after installing a larger main jet when what we're talking about a motocross bike,changing the needle clip, or some mysterious latent electrical problem is found.
    You'll look a long time.
    Then look at the posts where the poster finally says 'it was the rev limiter". There are dozens. :lol:
    Our job is to first provide the person with the problem with the most common, obvious and easiest solution, not to get into some intellectualizing that has them chasing their tail. Doug
  • Harrison
    Posts:4
    Joined:Tue Aug 05, 2008 8:33 pm

    by Harrison » Tue Aug 05, 2008 8:55 pm

    JD jeting makes a great kit that i used on my 150r it gives it more low end power and easier to control, it puts in a fatter jet then what its stock with and u have to put in fatter needles too. it makes it a lot better to handle in the trail.

Who is online

Users browsing this forum: No registered users and 1 guest