[KWPilot]

Anyone know of a good aftermarket gear shift lever that will fit the new CRF250F.

[JimDirt]

Welcome to the site !!

Hammerhead makes a shifter for it ...... They are pretty good quality ....

[craig.mcelroy]

Hammerhead makes a shifter for it ...... They are pretty good quality ....

@JimDirt, do you happen to have any specifics for it? I have searched all of the big vendors and can't seem to locate one that is listed as being compatible with this bike.

My daughter has gone through TWO stock shifters in 6 months, each from relatively minor tip overs in rocky terrain. May as well be made out of lead for how well they hold up.

[Back2-2]

Have you considered heating them and bending them back to shape? Pretty easy to do.

[JimDirt]

Hammerhead makes a shifter for it ...... They are pretty good quality ....

@JimDirt, do you happen to have any specifics for it? I have searched all of the big vendors and can't seem to locate one that is listed as being compatible with this bike.

My daughter has gone through TWO stock shifters in 6 months, each from relatively minor tip overs in rocky terrain. May as well be made out of lead for how well they hold up.

WPS(Western Power Sports) carries them , you can get them in standard length +10mm or +20mm longer , you have to buy thru a vendor (your local dealer or bike shop, as you can't buy direct from them) , I believe Ken (here) can get them as well , they are specific fitment from 2018-20 ... WPS Part # is 560-9407 for the standard length , they are around $34.95 Retail

[JimDirt]

Have you considered heating them and bending them back to shape? Pretty easy to do.

Neil ... your post count is 1111 ......

[craig.mcelroy]

Hammerhead makes a shifter for it ...... They are pretty good quality ....

@JimDirt, do you happen to have any specifics for it? I have searched all of the big vendors and can't seem to locate one that is listed as being compatible with this bike.

My daughter has gone through TWO stock shifters in 6 months, each from relatively minor tip overs in rocky terrain. May as well be made out of lead for how well they hold up.

WPS(Western Power Sports) carries them , you can get them in standard length +10mm or +20mm longer , you have to buy thru a vendor (your local dealer or bike shop, as you can't buy direct from them) , I believe Ken (here) can get them as well , they are specific fitment from 2018-20 ... WPS Part # is 560-9407 for the standard length , they are around $34.95 Retail

Thanks for the followup. The part you reference is for the 250R. Looking for the 250F like the OP which has a different form factor.
Checking WPS catalog matches my previous research that they don't have one (yet) for the 250F. It's similar to a couple other models based on my research, but nothing matches without some modification. Hoping not to have to buy an upgraded aftermarket and need to immediately turn around and heat it up and re-form it.

http://catalogs.wps-inc.com/2021/offroad/456/

[JimDirt]

My bad , I must have got mixed up looking thru the list , and missed the fact of the F was not listed and defaulted to the R out of habit

Unfortunately , for some of the newer bikes they just have not tooled up for them yet due to ongoing shipping and material issues .....I know my buddy has a 21 450R and he had to wait several months just to get a spare clutch lever for it ... stock or aftermarket (the 21 has a Hydraulic clutch) , unfortunately , with the way things are right now , everyone is behind , they are saying by winter the supply chains should be getting back to "normal" , though that does no one any good right now that need or want things .... I ordered a matching set of aftermarket hubs for a extra wheel set I am building for my 20 450R , I got the front right away (this was in May when I ordered everything) , I just finally got conformation my rear hub was in stock today , so it is on the way to me now ... but it took 3 months of being backordered to get it ...